Where to put a baby monitor camera: placement that works at night

This post contains affiliate links. If you buy through them, we may earn a small commission at no extra cost to you.Learn more.

Our answer, if you don’t read another word: the best place to put a baby monitor camera is high on a wall, angled down into the cot, and far enough back that the whole mattress is in frame rather than just the baby’s face. Ours are wall-mounted. Before you pick a spot, though, read the CPSC’s warning about monitor cords below, because where the cord runs is a safety question, and it comes first.

We own six video monitors and have two children sharing one nursery, so we have placed cameras over one cot and over two. This guide covers the placement decisions in detail. For the rest of setting up a new monitor, from pairing to sound settings, see how to use a baby monitor.

Start with the cord, and read the CPSC on it

This is the one part of placement we will not write our own advice for, because it is not ours to give.

The US Consumer Product Safety Commission has published a warning that infants and toddlers can strangle in baby monitor cords. In it, the CPSC and the Juvenile Products Manufacturers Association say to keep monitor cords at least three feet from any part of a crib, bassinet or play yard, and never to put a monitor inside a crib or on its edge. Read it yourself, and read the manual that came with your monitor, which will have its own instructions.

Monitor packaging does not always line up with that. Our VTimes VT31 comes with a mounting kit that includes a bracket for clipping the camera to a crib. The CPSC’s warning is the guidance to follow, not the accessories in a box.

Everything else on this page is about getting a good picture once that rule is respected.

Frame the whole cot, not the face

The most common mistake is framing too tight. A close shot of a sleeping face looks lovely on the first night. The first time the baby rolls, or shuffles down to the far end, it shows you an empty sheet.

Aim for the whole mattress in frame with a little margin around it. That way, wherever the baby ends up, they are on the screen. A wider frame also tells you more at a glance: whether they are lying down, sitting up or standing at the rail.

If your camera pans and tilts from the handset, you have some slack here, because a frame that is slightly off can be corrected from your bed. On our VAVA, swinging the camera with a button on the handset is the feature we use most. But it is still better to start with a placement that frames the whole cot without any steering.

Go high and look down

Height does more for the picture than anything else.

A camera at mattress level looks across the cot, through the rails, at the side of a baby. A camera mounted high looks down into it, over the rails, at the whole mattress. Looking down also means the cot’s own sides stop blocking the view, and a baby pressed against one edge is still visible.

Place it slightly to one side of the cot rather than straight overhead or straight ahead. A view from one corner, angled down, shows you the length of the mattress and the baby’s face from most sleeping positions.

Wall, shelf or dresser

Ours are on the wall, and it is the placement we would recommend if you can drill.

A wall mount keeps the camera exactly where you set it. Nobody knocks it while putting laundry away, and it does not slowly drift out of line. It gives you the height you need without furniture in the right place. It also keeps the camera out of a child’s reach, which matters more as they grow.

Most monitors come ready for it. Our Infant Optics includes mounting screws and an anchor in the box. The VAVA mounts on a wall or stands on a shelf. The VTech cameras stand on a table or go on a wall. The HelloBaby cameras can go on a ceiling, a wall, a shelf or a chest of drawers.

If you rent or cannot drill, a high shelf is the next best thing. Make sure nothing on that shelf can slide into the camera, and that the shelf itself respects the cord distance above. A dresser top is usually too low to look down into a cot, and it is where things get put down and knocked over.

Test the spot before you drill

A placement that looks right in daylight can be wrong at night, so try it out before making holes.

Put the camera in roughly the position you have in mind, on a temporary stand or a stack of books on a high surface, with the cord routed safely. Leave it there for a night or two. Check the picture once the night vision has switched on, and check it again when the baby has moved around. Then mount it.

This is also the time to check range. Carry the handset to every room you expect to use it in, with the camera where it will actually live.

Getting a good night picture

Night vision on every monitor we own is infrared, and infrared has a few habits that placement can make or break.

Do not shoot through glass. Infrared light bounces back off a window or a glass cabinet door, so a camera looking through glass shows you a glare of its own lights instead of the room.

Keep reflective surfaces away from the lens. A wall, a shelf edge or a picture frame right next to the camera can catch the infrared and wash out the picture. Give the camera a clear view with nothing in front of it.

Watch out for windows in the daytime too. A camera pointed towards a bright window will struggle for naps, as the window blows out and the cot falls into shadow. Angle it so the window is behind or beside the camera rather than in front of it.

If the night picture is still disappointing after all that, the camera may simply be the limit. Our best baby monitor roundup notes which of ours hold up after dark.

Hearing as well as seeing

The camera holds the microphone too, so placement decides what you hear as much as what you see.

Keep the camera away from the noisiest thing in the room. A fan, an air purifier or a heater right next to the camera will pour steady noise into the handset all night. The further apart they are, the more of the baby you hear.

Some monitors deal with this better than others. Our Infant Optics filters out steady background noise, so the fan barely reaches the handset. If yours does not, placement is your noise filter.

Two cots in one room

This is our setup, so we have tried both ways.

The option we prefer is one camera per cot. Each camera is framed on its own cot and both show on a split-screen handset. You can see at a glance which child is awake without touching anything. Our two-camera VAVA works this way, and so does the HelloBaby.

Resist pulling one camera back far enough to fit both cots in a single wide shot. It sounds efficient. At night it turns each child into a shape in the dark. We tried it with our single-camera VTech, which has a good field of view, and still ended up running a second monitor beside it.

If you have one camera that pans, put it roughly between the cots and high up, so a short turn from the handset swings it from one to the other. Our VAVA’s cameras can do that from a button on the handset. It works well, with the trade that you are choosing which child to look at rather than seeing both, which is why the VAVA, like the HelloBaby, also ships with a second camera.

Lenses and zoom change where the camera can go

The Infant Optics is the only monitor we own where placement has a hardware answer. It comes with a standard lens and an optical zoom lens that swap over in seconds, and a wide-angle lens is sold separately. A frame that is too tight or too wide becomes a lens change instead of a new screw hole.

The zoom lens also lets the camera sit further back and still show detail, which helps when you are keeping it well away from the cot. Digital zoom, which every other monitor we own uses, only crops the picture, so the further away the camera is, the softer a zoomed view gets. More on that in our Infant Optics baby monitor review.

Where the handset goes

The camera is half the job. The parent unit needs a good spot too.

Signal first. Monitors like ours talk over 2.4 GHz radio, and walls, floors and appliances weaken it. Microwave ovens also work around 2.4 GHz and can interfere while running. Range figures on boxes assume open air, and ours have a couple of dead spots in the corner of the house furthest from the nursery. Find yours in the first week and avoid them.

Then the surface. Put the handset somewhere it cannot be knocked off. Our VTech’s kickstand sits off-centre under a fairly large unit, and it tips over easily, so it lives flat against something.

Then power. A handset with an evening-length battery, like the VAVA’s, will live on its charger by the bed, so put the charger where you can reach the screen without getting up. A handset rated for longer, like the Jeeber’s 8 to 16 hours with its screen-off mode, can go wherever you are.

A quick placement checklist

Checks before you mount a baby monitor camera
CheckWhat you want
CordsRead the CPSC warning and your manual first
FrameThe whole mattress in shot, with a margin
HeightHigh, looking down into the cot over the rails
AngleFrom one corner, slightly to the side
MountWall if you can drill, high shelf if not
Night pictureNo glass in front, nothing reflective near the lens
DaytimeWindow beside or behind the camera, not in front
SoundAway from fans, purifiers and heaters
Two cotsOne camera per cot, or one pannable camera between them
HandsetClear of dead spots, on a surface it cannot fall from

The bottom line

Where to put a baby monitor camera comes down to a few rules. Read the CPSC’s cord warning and your manual before anything else. Then go high, look down from one corner, frame the whole cot, and keep glass, reflective surfaces and fans away from the lens. Test the spot for a night before you drill. With two cots, give each its own camera if you can.

If you are still choosing a monitor, our how to choose a baby monitor guide covers what to look for, and the best baby monitor roundup ranks the ones we own. For the rest of the setup, how to use a baby monitor picks up where this page leaves off.

Frequently asked questions

Where is the best place to put a baby monitor camera?

High on a wall, angled down into the cot, and far enough back that the whole mattress is in the frame rather than just the baby's face. That view keeps working when the baby rolls or shuffles to a corner. Before you choose a spot, read the CPSC's warning about baby monitor cords and the manual that came with your monitor, because cord placement near a cot is a safety question rather than a framing one.

How far should a baby monitor be from the crib?

The CPSC and the Juvenile Products Manufacturers Association have said to keep baby monitor cords at least three feet from any part of a crib, bassinet or play yard, and never to put a monitor inside a crib or on its edge. Read the CPSC's warning yourself and follow the manual for your own monitor. We are a gear blog, and the safety guidance belongs with them.

Should a baby monitor camera be mounted on the wall?

Ours are, and it is the placement we would recommend if your walls allow it. A wall mount puts the camera high enough to look down into the cot, keeps it from being knocked or moved, and keeps it out of reach. Most monitors include a bracket or screws. A high shelf is the next best option if you cannot drill.

Where do you put a baby monitor camera for two cots?

Our preference is one camera per cot, each framed on its own cot, with both shown on a split-screen handset. A single wide shot of two cots turns both children into shapes at night. If you have one camera, place it where it can pan between the cots from the handset, roughly central and high, so a small turn swings it from one cot to the other.

Why is my baby monitor night vision blurry or washed out?

Usually because of where the camera is. Infrared light bounces back off glass, so a camera looking through a window or a glass-fronted cabinet will glare. A wall or surface close to the lens can reflect infrared back and wash the picture out. Move the camera so it has a clear, open view of the cot and nothing reflective right in front of it.